Written By :

Connor

/

/

Dishwasher

Expert Author

How to Test Dishwasher Drain Pump

A dishwasher that refuses to drain is a common and frustrating household problem. When you open the door after a cycle, expecting sparkling clean dishes, ...

How to Test Dishwasher Drain Pump

A dishwasher that refuses to drain is a common and frustrating household problem. When you open the door after a cycle, expecting sparkling clean dishes, and instead find a pool of murky, stagnant water, it’s clear something is wrong. More often than not, the culprit is a malfunctioning drain pump, the component responsible for expelling wastewater from the appliance.

Learning to test the drain pump yourself can save you a significant amount of money on a service call and get your kitchen back to normal much faster. This guide on how to test dishwasher drain pump will walk you through the process, providing a detailed, step-by-step approach to diagnosing the issue. With a few common tools and some patience, you can confidently determine if your drain pump needs to be replaced.

Tools and Materials You’ll Need

  • Multimeter (digital or analog)
  • Screwdriver set (Phillips and flathead)
  • Nut driver set or adjustable wrench
  • Pliers (needle-nose and channel-lock)
  • Towels or rags
  • Shallow pan or bucket
  • Work gloves
  • Safety glasses
  • Flashlight or headlamp

8 Simple Step-By-Step Guidelines on How to Test Dishwasher Drain Pump

Step 1: Disconnect Power and Water Supply

Before beginning any work on your dishwasher, your absolute first priority must be safety. Start by completely disconnecting the appliance from its power source. For most dishwashers, this involves unplugging the power cord from the wall outlet, which may be located under the sink or in an adjacent cabinet.

Start by completely disconnecting the appliance from its power source

If the dishwasher is hardwired directly into your home’s electrical system, you must go to your main circuit breaker panel and switch off the breaker that corresponds to the dishwasher. Confirm the power is off by trying to turn the dishwasher on; it should be completely unresponsive. This step is non-negotiable and prevents the risk of serious electrical shock.

Once the power is confirmed to be off, you need to shut off the water supply to the dishwasher. Look for a shut-off valve, typically located under the kitchen sink, connected to the hot water line that runs to the appliance.

The valve usually has a small handle that you can turn clockwise to close it. If you can’t find a dedicated valve for the dishwasher, you will need to shut off the main water supply to your entire house for the duration of the repair. This critical step prevents any water from flowing into the dishwasher while you are working, avoiding potential leaks and water damage to your kitchen floor and cabinets.

Step 2: Access the Drain Pump

With the power and water safely disconnected, you can now prepare to access the internal components. Most dishwashers are installed under a countertop and secured with mounting brackets. Use a screwdriver or nut driver to remove the screws holding these brackets in place. They are usually found along the top or sides of the dishwasher frame, just inside the opening.

Once the screws are removed, you can carefully begin to slide the dishwasher out of its cabinet space. Be gentle and pull it out just far enough to give yourself comfortable working room behind and underneath it. Lay down old towels or a shallow pan to catch any residual water that will likely spill from the hoses.

The drain pump is located at the base of the dishwasher, typically near the front for easier access. To get to it, you will likely need to remove a lower access panel. This panel is usually held in place by a few screws or clips. Remove the screws and set them aside in a safe place. Once the panel is off, you should have a clear view of the motor, pump, and various hoses at the bottom of the unit. Use a flashlight to identify the drain pump.

The Drain Pump is Located at 
the Base of the Dishwasher

It is a small component with two connections: an electrical connector and a drain hose. The owner’s manual for your specific dishwasher model can be an invaluable resource here, as it will often include a diagram showing the exact location of the pump.

Step 3: Inspect the Drain Path for Blockages

Before you test the pump’s electrical function, it’s essential to rule out a simpler problem: a physical blockage. A clog in the drain path is a very common reason for a dishwasher’s failure to drain, and it can often mimic the symptoms of a failed pump.

Start your inspection at the point where the dishwasher’s drain hose connects to your sink’s plumbing or garbage disposal. Disconnect this hose by loosening its clamp with a screwdriver or pliers. Have a bucket ready, as water trapped in the hose will flow out. Check the end of the hose and the connection point on the plumbing for any food debris or buildup that could be causing an obstruction.

Disconnect This Hose by Loosening 
Its Clamp With a Screwdriver

Next, inspect the drain hose itself along its entire length for any kinks or sharp bends that might be restricting water flow. Then, move to the inside of the dishwasher. Remove the lower dish rack to get a clear view of the bottom of the tub. Locate the filter assembly, which usually consists of a cylindrical filter and a flat mesh screen.

Twist and lift the filter out, then remove the screen. These components are designed to catch food particles and can become severely clogged over time. Thoroughly clean the filter and screen under running water. Use a flashlight to look down into the sump area beneath the filter to check for larger debris, like broken glass or bones, that could be blocking the pump’s inlet.

Step 4: Disconnect the Drain Pump

Now that you have confirmed the drain path is clear, you can proceed with disconnecting the pump itself for testing. Begin by detaching the drain hose from the pump outlet. This hose is usually secured with a spring or screw clamp.

Use pliers or a screwdriver to loosen the clamp and carefully wiggle the hose off the pump’s nipple. Be prepared for more residual water to drain out, so keep your towels and pan handy. Take this opportunity to visually inspect the inside of the pump’s outlet for any visible debris that you might have missed earlier.

Use Pliers or a Screwdriver to 
Loosen the Clamp and Carefully

With the hose removed, the next step is to disconnect the electrical wiring. The pump is connected to the dishwasher’s main wiring harness via a plastic connector or two individual wires. If it’s a single plastic connector, there will be a small locking tab that you need to depress with a small flathead screwdriver or your fingernail before you can pull it apart.

If there are two separate wires, simply pull them off their respective spade terminals on the pump. Pay close attention to the orientation of the wires or take a quick photo with your phone before disconnecting them. This will serve as a crucial reference to ensure you reconnect them correctly later.

Step 5: Remove the Drain Pump from the Dishwasher

With all hoses and wires disconnected, you are ready to physically remove the drain pump from the dishwasher assembly. The method for removal can vary slightly between different brands and models. Most commonly, the pump is secured to the main sump housing by a few screws or through a simple twist-lock mechanism.

If it is held by screws, use the appropriate screwdriver or nut driver to remove them completely. Keep these screws in a labeled bag or container so you don’t misplace them, as they are essential for reassembly.

If your dishwasher uses a twist-lock system, you will need to rotate the pump, usually about a quarter-turn counterclockwise, to release it from its housing. It may be a tight fit, so you might need to apply firm, steady pressure to get it to turn.

Once it’s unlocked, you should be able to pull the pump straight out. In some designs, the pump and motor are a single integrated unit, while in others, the pump can be separated from the motor. If they can be separated, you will typically need to remove a few more screws holding the pump body to the motor. Consulting your appliance’s service manual can provide specific instructions for your model.

Step 6: Test the Pump Motor for Continuity

Now that you have the drain pump removed and on your workbench, you can perform an electrical test using a multimeter. This test will check for continuity, which confirms that the electrical winding inside the pump’s motor is intact and can form a complete circuit.

A break in this winding means the motor is burned out and the pump must be replaced. Set your multimeter to the lowest setting for Ohms (Ω) of resistance. If your multimeter has an audible continuity setting, you can use that as well, as it will beep if a complete circuit is detected.

Perform an Electrical Test 
Using a Multimeter

Take the two probes of your multimeter and touch them to the two metal electrical terminals on the pump where you previously disconnected the wires. The polarity of the probes does not matter for this test.

A functional pump motor should give you a resistance reading, typically somewhere between 15 and 40 Ohms. The exact value will vary by manufacturer, but the important thing is that you get a fixed, measurable reading. If the multimeter display shows “OL” (Open Line), infinite resistance, or doesn’t change from its default reading, it indicates a break in the motor’s winding. This confirms the pump is electrically faulty and is the reason your dishwasher is not draining.

Step 7: Test for a Short to Ground

In addition to testing for continuity, it is also important to test for a short to ground. A short to ground occurs when the internal motor winding has deteriorated and is making electrical contact with the metal casing of the pump. This is a dangerous condition that can cause the pump to malfunction and could trip your circuit breaker.

This test will help you identify if such a fault exists, which also necessitates the replacement of the pump. Keep your multimeter set to the Ohms of resistance setting for this test.

To perform the test, touch one of your multimeter’s probes to one of the pump’s electrical terminals. Then, touch the other probe to a clean, unpainted metal part of the pump’s casing. A good, safe pump should show an “OL” or infinite resistance reading on the multimeter.

Touch One of Your Multimeter's Probes to 
One of the Pump's Electrical Terminals

This indicates that there is no electrical connection between the motor windings and the pump’s external housing. Repeat the test by moving the first probe to the other electrical terminal while keeping the second probe on the metal casing. If you get any numerical resistance reading during either of these tests, it means the pump has a short to ground and is unsafe to use. It must be replaced immediately.

Step 8: Reassemble or Replace the Pump

Based on the results of your tests, you will either reassemble the dishwasher with the old pump or install a new one. If both the continuity and ground tests passed, your pump is likely in good working order electrically. The drainage problem may stem from an intermittent issue, a faulty control board, or a clog you missed.

In this case, you can reinstall the original pump. Carefully position the pump back into its housing, securing it with the twist-lock mechanism or the screws you set aside. Reconnect the electrical wiring harness, ensuring the connector clicks securely into place. Then, reattach the drain hose and tighten its clamp firmly.

If your tests revealed that the pump failed either the continuity test or the short-to-ground test, you will need to replace it. Purchase a new pump that is a certified replacement for your specific dishwasher model number. The installation of the new pump is simply the reverse of the removal process. Secure the new pump in place, connect the wiring, and attach the drain hose.

Once everything is reassembled, carefully slide the dishwasher back into its cabinet. Reinstall the mounting bracket screws and the lower access panel. Finally, turn the water supply and the circuit breaker back on. Run a short rinse or drain cycle to test the new pump and check thoroughly for any leaks around the new connections.

Following these steps on how to test dishwasher drain pump, it is also important to maintain and clean the dishwasher regularly to ensure its proper functioning.

Frequently Asked Questions

Q1: Why Is My Dishwasher Not Draining?

A1: A dishwasher may fail to drain for several reasons. The most common cause is a blockage in the drain system, which can occur in the filter, the drain hose, the air gap (if present), or the garbage disposal connection. Another primary culprit is a failed drain pump, where the motor has burned out and can no longer force water out.

Less common issues include a faulty lid switch on the detergent dispenser, which can prevent the cycle from advancing to the drain phase, or a malfunctioning electronic control board that isn’t sending the signal to the pump to activate.

Q2: How Do I Know if My Dishwasher Pump Is Bad?

A2: There are several signs that point to a bad dishwasher pump. The most obvious symptom is standing water left in the bottom of the tub after a cycle is complete. You might also hear unusual noises during the drain cycle,

such as a humming sound without any water movement, which suggests the motor is receiving power but is seized. Conversely, a complete lack of any sound from the pump during the drain portion of the cycle could indicate the motor has failed entirely. The definitive way to know is to perform the multimeter tests for continuity and shorts as detailed in this guide.

Q3: Can I Just Clean My Dishwasher Drain Pump?

A3: Yes, cleaning the drain pump area is an excellent first step in troubleshooting. Many drainage problems are caused by debris like food particles, broken glass, or small plastic items physically obstructing the pump’s impeller.

Cleaning the Drain Pump Area is an Superb 
First Step in Troubleshooting

By accessing the pump, you can often remove the object and restore normal function without needing to replace the part. However, if the pump’s motor is electrically faulty (as determined by a multimeter test), no amount of cleaning will fix it. In that case, the entire pump unit must be replaced with a new one.

Q4: How Much Does It Cost to Replace a Dishwasher Drain Pump?

A4: The cost to replace a dishwasher drain pump can vary significantly based on whether you do it yourself or hire a professional. If you perform the repair yourself, your only cost is the part itself, which typically ranges from $40 to $100, depending on the brand and model of your dishwasher.

If you hire a professional appliance repair technician, you must also account for labor costs. A service call and labor can add an additional $150 to $250 to the total cost, bringing the professional replacement price to a range of approximately $200 to $350.

Conclusion

Successfully testing your dishwasher’s drain pump is a manageable task that empowers you as a homeowner. By following these steps on how to test dishwasher drain pump methodically, you can accurately diagnose whether the pump is the source of your drainage woes or if the problem lies elsewhere. This knowledge not only saves you from the cost and hassle of a professional service visit but also provides a deeper understanding of how your appliances work.

Regular maintenance, such as cleaning your dishwasher’s filter, is key to preventing future issues and extending the life of the pump. Whether you end up cleaning a simple clog or replacing a faulty motor, taking on this repair yourself is a rewarding and cost-effective solution.