Written By :

Connor

/

/

Dishwasher

Expert Author

How to Fix Amana Dishwasher Not Draining

A dishwasher that refuses to drain is a frustrating discovery, leaving you with a puddle of dirty, stagnant water and a pile of unclean dishes. ...

How to Fix Amana Dishwasher Not Draining

A dishwasher that refuses to drain is a frustrating discovery, leaving you with a puddle of dirty, stagnant water and a pile of unclean dishes. This common household problem can bring your kitchen routine to a halt. Fortunately, for Amana dishwasher owners, a draining issue is often something you can diagnose and fix yourself without needing to call for an expensive repair service.

This guide on how to fix amana dishwasher not draining is designed to walk you through the process, from simple checks to more involved component inspections. By following these steps, you can identify the cause of the blockage and restore your appliance to proper working order. With a little patience and a few basic tools, you can tackle this issue and get your dishwasher running smoothly again.

Tools and Materials You’ll Need

Before you begin, gather the following items to ensure the repair process is as smooth as possible:

  • Screwdriver (Phillips and flat-head)
  • Pliers (needle-nose and channel-lock)
  • Bucket
  • Old towels or rags
  • Flashlight
  • Protective gloves
  • Shop vacuum (optional, but helpful)
  • Wire hanger or plumber’s snake
  • Multimeter (for checking electrical components)
  • Replacement parts (if a component is found to be faulty)

7 Simple Step-by-step Guidelines on How to Fix Amana Dishwasher Not Draining

Step 1: Disconnect Power and Water Supply

The most critical first step in any appliance repair is to ensure your safety by completely disconnecting the unit from its power source. For a dishwasher, this usually means locating the circuit breaker in your home’s electrical panel and switching it to the “off” position. Some installations may have a dedicated power switch under the sink or a cord that can be unplugged from a nearby outlet. Never assume the appliance is off just because it’s not running a cycle; always verify by checking the breaker or unplugging the unit directly to prevent any risk of electric shock while you work.

completely disconnecting the unit from its power source

Once the power is turned off, you should also shut off the water supply to the dishwasher. The shut-off valve is typically located under the kitchen sink, connected to the hot water line. Turning the valve clockwise will stop the flow of water. This step prevents any accidental flooding or water spillage while you are inspecting the drain lines and internal components. Placing old towels or rags on the floor around the base of the dishwasher is also a wise precaution to soak up any residual water that will inevitably spill during the repair process.

Step 2: Clear the Dishwasher Filter and Sump

Often, the simplest explanation for a draining problem is a clogged filter. The filter is designed to catch large food particles and debris, preventing them from entering the drain pump. Over time, it can become completely blocked, obstructing water flow. To access it, remove the bottom dish rack. You will find the filter assembly at the bottom of the dishwasher tub. Most Amana models have a cylindrical filter that you can twist and pull out, along with a flat mesh screen underneath. Take both parts to the sink for a thorough cleaning.

You Will Find the Filter Assembly at 
the Bottom of the Dishwasher Tub

Use a soft brush and warm, soapy water to scrub away any accumulated grime, grease, and food residue. Rinse the components completely before reinstalling them. While the filter is out, use a flashlight to inspect the area beneath it, known as the sump. This is where water collects before being pumped out. Carefully remove any visible debris you find in the sump area. A clean filter and clear sump are essential for proper drainage, and maintaining them regularly can prevent this issue from happening in the future.

Step 3: Inspect the Drain Hose for Kinks and Clogs

The drain hose is the long, ribbed tube that carries wastewater from the dishwasher to your sink’s plumbing or garbage disposal. It typically runs from the back of the appliance, through the cabinetry, to the drain connection under the sink. Begin by visually inspecting the entire length of the hose for any sharp bends, kinks, or twists that could be restricting water flow. Sometimes, simply straightening out a kinked hose is all that’s needed to solve the problem. Also, check to ensure the hose has a “high loop” — it should be fastened to the underside of the countertop to prevent sink water from flowing back into the dishwasher.

If there are no visible kinks, the hose may be clogged internally. Disconnect the end of the hose from the garbage disposal or sink drain pipe; be ready with a bucket to catch any water that drains out. Point the disconnected end into the bucket and check for obstructions. You can use a straightened wire hanger or a small plumber’s snake to gently probe the hose and dislodge any blockages. For a more thorough cleaning, you can completely detach the hose from the dishwasher itself (this may require pulling the unit out from under the counter) and flush it with high-pressure water.

Step 4: Check the Garbage Disposal and Air Gap

If your dishwasher drains into a garbage disposal, it’s a common source of drainage problems. Food waste inside the disposal can easily block the small inlet where the dishwasher hose connects. To check this, first run the garbage disposal for about 30 seconds with cold water to clear out any debris. If the dishwasher still doesn’t drain, you’ll need to disconnect the drain hose from the disposal inlet port. Use a small screwdriver or a bottle brush to carefully clean out the inlet, removing any hardened food particles or buildup that may have accumulated there.

First Run the Garbage Disposal 
for About 30 Seconds

Some plumbing codes require an air gap, which is a small cylindrical fixture mounted on your countertop or sink. Its purpose is to prevent contaminated water from the sink from siphoning back into the dishwasher. These devices can become clogged with debris over time. To inspect it, simply twist and pull off the decorative chrome cover. You will see a smaller plastic cap underneath; remove that as well to expose the internal chamber. Clean out any gunk you find inside the air gap and on the cap, and ensure the small hoses connected to its base are clear before reassembling.

Step 5: Examine the Check Valve

The check valve is a small but important component that prevents dirty water from flowing back into the dishwasher tub after it has been pumped out. If this valve is stuck shut or clogged with debris, it will prevent water from leaving the dishwasher in the first place. The check valve is usually located in the sump assembly, near where the drain hose connects to the dishwasher pump. You may need to remove the filter, filter screen, and a few screws holding the sump cover in place to access it.

Once you have located the check valve (it is often a small rubber flap), inspect it for any debris that might be holding it in place. Carefully clean the valve and the area around it. Test the flap with your finger to ensure it moves freely; it should open easily in one direction and seal shut in the other. If the rubber appears warped, torn, or has hardened to the point where it no longer seals properly, it will need to be replaced. A faulty check valve is an inexpensive part that can cause significant draining issues.

Step 6: Test the Drain Pump

If all the hoses and filters are clear, the problem may lie with the drain pump itself. The drain pump is a motor responsible for actively forcing wastewater out of the dishwasher. You will need to pull the dishwasher out from under the counter and likely tilt it on its side or back to access the pump, which is mounted to the bottom of the tub. First, perform a visual inspection of the pump’s impeller—the small, fan-like blades that push the water. Small, hard objects like glass shards or fruit pits can jam the impeller and stop it from spinning.

If the impeller is clear and spins freely, the pump’s motor may have failed electrically. You can test this using a multimeter set to the ohms setting. After disconnecting the wires from the pump, touch the multimeter probes to the pump’s electrical terminals. A functional motor should show a resistance reading, typically between 15 and 40 ohms (consult your dishwasher’s technical sheet for the exact value). If the multimeter reads infinity (OL), it indicates an open circuit, meaning the motor has burned out and the entire drain pump assembly must be replaced.

Test the Door Switch for 
Continuity With a Multimeter

Step 7: Inspect the Door Switch and Control Board

In some cases, the dishwasher may not drain because it doesn’t think the cycle is complete or that the door is properly closed. The door switch (or latch assembly) is a safety mechanism that confirms the door is securely shut before allowing the dishwasher to run certain functions, including the final drain. If this switch is faulty, it may fail to send the “door closed” signal to the control board, preventing the drain cycle from initiating. You can test the door switch for continuity with a multimeter. A working switch will show continuity when the door latch is engaged.

As a final resort, the issue could be with the main control board, which is the dishwasher’s electronic brain. A malfunctioning control board can fail to send power to the drain pump at the correct time in the cycle. This is more difficult to diagnose without professional equipment and expertise. Visually inspect the board for any obvious signs of damage, such as burn marks or loose connections. If you have exhausted all other possibilities and suspect the control board is the culprit, it is often best to consult a professional technician, as this is an expensive component and replacing it incorrectly can cause further damage.

Inspect the Board for Any 
Obvious Signs of Damage

Following these steps on how to fix amana dishwasher not draining issue can save you time and money, as well as possibly preventing the need for a costly repair or replacement. Regular maintenance and proper use of your dishwasher can also help prevent these issues from occurring in the first place.

Common Mistakes to Avoid

  • Forgetting to disconnect the power and water supply before starting work.
  • Using harsh chemical drain cleaners can damage plastic and rubber components.
  • Applying too much force and cracking plastic parts like the filter or pump housing.
  • Failing to re-secure the drain hose with a high loop causes backflow issues.
  • Incorrectly reassembling components, leading to leaks or improper function.

Do You Need To Use Professionals?

While many draining issues can be resolved with DIY methods, there are times when calling a professional is the best course of action. If you have followed all the steps above and the dishwasher still won’t drain, it’s a sign of a more complex problem. You should also call for service if you suspect an issue with the main control board or are uncomfortable working with electrical components like motors and switches.

If the repair requires pulling out the entire dishwasher and you are not confident in doing so without damaging your floors or cabinetry, a technician has the right tools and experience to handle it safely. Finally, if your appliance is still under warranty, attempting a DIY repair could void it, making a professional service call the wiser choice.

How Much Will It Cost?

The cost to fix a non-draining Amana dishwasher can vary significantly based on the cause of the problem. If the issue is a simple clog in the filter or drain hose that you can fix yourself, the cost is virtually zero. Should you need to replace a part, the expenses are generally modest. A new check valve or drain hose typically costs between $15 and $40.

Significantly Based on 
the Cause of the Problem

A replacement drain pump is more expensive, usually ranging from $50 to $150, depending on the model. If you decide to hire a professional, you can expect to pay a service fee of $75 to $150 just for the visit, plus the cost of parts and labor, which can bring the total repair bill to anywhere from $150 to over $400, especially if the control board needs replacement.

Frequently Asked Questions

Q1: Why Is There Standing Water In The Bottom Of My Dishwasher?

A1: Standing water is the most common sign of a drainage problem. This can be caused by a variety of issues, including a clogged filter at the bottom of the tub, a blocked or kinked drain hose, or a blockage in your sink’s plumbing or garbage disposal where the dishwasher drains. It could also indicate a mechanical failure, such as a jammed or broken drain pump that is unable to force the water out of the appliance.

Q2: How Often Should I Clean My Amana Dishwasher Filter?

A2: To prevent clogs and maintain optimal performance, it is recommended to clean your dishwasher filter at least once a month. If you frequently wash dishes with heavy food soils or notice odors, you may want to clean them more often. Regular cleaning only takes a few minutes and is the most effective way to prevent the majority of drainage issues before they start.

Q3: Can I Run The Dishwasher If It Has Standing Water?

A3: It is not advisable to run another cycle if there is already standing water in the dishwasher. Doing so will only add more water to the tub, increasing the risk of an overflow and potential water damage to your kitchen floor and cabinets. You should first address the drainage problem and remove the existing water before attempting to use the appliance again.

Q4: What Is The High Loop On A Dishwasher Drain Hose?

A4: A high loop is a critical part of the drain hose installation. It involves securing the hose as high as possible under the sink, ideally to the underside of the countertop, before it connects to the garbage disposal or drain pipe. This loop uses gravity to prevent dirty water from the sink from flowing backward into the dishwasher, which can contaminate your clean dishes and cause drainage problems.

Conclusion

Facing a dishwasher full of murky water is never pleasant, but it doesn’t always signal a need for a costly professional repair or a brand-new appliance. By systematically working through these troubleshooting steps on how to fix amana dishwasher not draining, you can effectively diagnose and fix the most common causes behind an Amana dishwasher that fails to drain. From cleaning filters and clearing hoses to inspecting valves and pumps, you are now equipped with the knowledge to tackle this problem head-on.

Remember to prioritize safety by always disconnecting the power and water before you begin. With patience and the right approach, you can restore your dishwasher’s function, saving yourself time, money, and the inconvenience of hand-washing dishes. Regular maintenance, such as cleaning the filter, will go a long way in preventing this issue from recurring in the future.