Written By :

Connor

/

/

Dishwasher

Expert Author

How to Install a Whirlpool Dishwasher

Installing a new Whirlpool dishwasher can be a rewarding home improvement project. A successful installation not only saves you money but also gives you a ...

Installing a new Whirlpool dishwasher can be a rewarding home improvement project. A successful installation not only saves you money but also gives you a sense of accomplishment. This guide on how to install a whirlpool dishwasher will walk you through the process, making it simple and manageable, even for those with limited DIY experience.

How to Install a Whirlpool Dishwasher

Following a clear set of instructions is key to ensuring your new appliance works correctly and safely. We’ve broken down the installation into easy-to-follow steps, from preparing your space to running the first test cycle. With the right tools and a little patience, you can have your dishwasher ready to tackle dirty dishes in no time.

Tools and Materials You’ll Need

  • Adjustable wrench
  • Pliers
  • Screwdriver set (Phillips and flathead)
  • Drill with various bits
  • Tape measure
  • Level
  • Bucket and towels
  • Safety gloves
  • Safety glasses
  • Flashlight or headlamp
  • Dishwasher installation kit (often includes a new water supply line and fittings)
  • Wire nuts
  • Teflon tape (plumber’s tape)

7 Simple Step-By-Step Guidelines on How to Install a Whirlpool Dishwasher

Step 1: Prepare the Space and Turn Off Utilities

Before you begin any work, your first priority is safety and preparation. Start by completely turning off the power to the existing dishwasher from your home’s circuit breaker panel. It’s a good practice to use a voltage tester to confirm there is no electrical current at the dishwasher’s junction box. Next, shut off the water supply.

Turning Off the Power

This is typically done via a small valve located under the kitchen sink, connected to the hot water line. Place a bucket and some old towels under the sink and around the old dishwasher to catch any residual water that will drain from the hoses during removal. Taking these initial precautions is crucial to prevent electrical shock or water damage.

Once the utilities are safely disconnected, you can prepare the cabinet opening. If you are replacing an old unit, you will need to disconnect its water supply line, drain hose, and electrical wiring before carefully sliding it out.

Measure the height, width, and depth of the opening to ensure your new Whirlpool dishwasher will fit. The space should be clean, dry, and free of any debris. Check that the flooring is level. If you are installing a dishwasher for the first time, you will need to ensure you have the necessary plumbing and electrical connections roughed in and accessible within the cabinet space.

Step 2: Unbox and Inspect the New Dishwasher

Carefully unbox your new Whirlpool dishwasher, making sure to remove all packaging materials, including cardboard, foam, and plastic wrapping. It is a good idea to lay a blanket or a piece of cardboard on the floor to prevent scratching the appliance or your flooring. Gently lay the dishwasher on its back to access the underside.

This is where you will find the installation manual and often a small parts kit. Take a moment to review the manufacturer’s instructions, as they will provide specific details for your model. It’s also a good time to identify all the connection points for the water supply, drain, and electrical wiring.

While the dishwasher is on its back, take the opportunity to attach any necessary fittings. The dishwasher installation kit you purchased should contain a 90-degree elbow fitting for the water inlet valve. Wrap the threads of the elbow fitting with Teflon tape, winding it clockwise three to four times to create a watertight seal.

Then, carefully thread it into the dishwasher’s water inlet valve and tighten it with an adjustable wrench. Be careful not to overtighten, as this could crack the plastic valve. You can also pre-thread the new water supply line onto this fitting, but leave it loose for now. Finally, adjust the dishwasher’s leveling legs to a preliminary height, ensuring they are screwed in enough to easily slide the unit into the opening.

Step 3: Connect the Drain Hose

Connecting the drain hose is a critical step to prevent dirty water from backing up into your dishwasher or sink. Most Whirlpool models come with a drain hose attached. You will need to route this hose from the back of the dishwasher to the drain connection under your sink.

The most common connection points are either a dedicated nipple on your garbage disposal or a Y-branch tailpiece on your sink’s drain pipe. If you are connecting to a garbage disposal for the first time, you may need to knock out a small plug inside the disposal’s drain nipple using a screwdriver and hammer. Be sure to retrieve the plastic plug from inside the disposal before proceeding.

To ensure proper drainage and prevent siphoning, you must create a “high loop” with the drain hose. This involves routing the hose up as high as possible under the sink, ideally just below the underside of the countertop, before it connects to the disposal or drain pipe.

You can secure the hose in this high position using a strap or zip tie. This high loop creates an air gap that stops sink water from flowing back into the dishwasher. Once the high loop is secured, attach the end of the drain hose to the connection point and secure it firmly with a hose clamp.

Step 4: Position the Dishwasher and Connect the Water Supply

Before sliding the dishwasher into place, it’s time to route the water supply line and the electrical cable. Feed the new flexible, braided steel water supply line from the hot water valve under the sink towards the front of the cabinet opening. Do the same with the electrical cable from the junction box. Now, you can carefully slide the dishwasher into the cabinet.

Move it slowly, ensuring that the drain hose, water line, and electrical cable are not kinked, pinched, or tangled behind the unit. Push the dishwasher back until the front door is nearly flush with your cabinets, leaving a few inches of space to work.

From underneath the sink, connect the water supply line to the hot water shut-off valve. If you are reusing an old fitting, you may need to replace the compression nut and ferrule to ensure a tight seal. Tighten the connection securely with an adjustable wrench, but avoid overtightening.

Now, reach under the front of the dishwasher and connect the other end of the water supply line to the 90-degree elbow you attached earlier. Once both ends are connected, turn the water supply on very slowly and carefully check for any leaks at both connection points. Have a towel ready to catch any drips and tighten the fittings slightly if you notice any leaks.

Step 5: Complete the Electrical Connections

With the power still turned off at the circuit breaker, you can now make the electrical connections. The dishwasher’s junction box is usually located at the front, behind the bottom access panel. Remove the junction box cover to expose the wiring.

Remove the Junction 
Box Cover

Your home’s electrical cable will have three wires: a black (hot) wire, a white (neutral) wire, and a green or bare copper (ground) wire. The dishwasher will have a corresponding set of wires. Carefully pull the electrical cable you previously routed into the junction box through the strain relief clamp and tighten the clamp to secure it.

Using wire nuts, connect the wires by color: black to black, white to white, and ground to ground (or to the green grounding screw provided). Twist the wire nuts on securely to ensure a solid connection and give each wire a gentle tug to make sure it is held firmly in place. Neatly tuck the wires back into the junction box and replace the cover.

This is a crucial safety step, so double-check that all connections are secure and that no bare wires are exposed. If you are not comfortable with electrical work, this is the best time to call a qualified electrician to complete the job safely.

Step 6: Secure the Dishwasher and Reinstall Panels

Now that all the connections are made, you can push the dishwasher the final few inches into the cabinet opening. Use a level to check that the unit is level from front to back and side to side. You can adjust the leveling legs at the bottom of the dishwasher as needed.

Most Whirlpool models have adjustable rear legs that can be raised or lowered by turning a screw located at the front center base of the unit. A level dishwasher ensures proper water distribution and drainage during cycles. Once level, it’s time to secure the appliance to the countertop or adjacent cabinets to prevent it from tipping forward when the door is opened.

Your dishwasher will come with mounting brackets that can be attached to the top or sides of the unit. If you have a laminate or wood countertop, you can drive the provided screws through the top mounting brackets directly into the underside of the countertop. For stone countertops like granite or quartz, you will use the side mounting option.

Attach the brackets to the sides of the dishwasher and drive screws into the adjacent cabinet frames. Do not overtighten the screws, as this can warp the dishwasher tub. Finally, reinstall the lower access panel and the toe-kick plate at the bottom of the dishwasher.

Step 7: Test the Dishwasher

The final step is to test your installation. Turn the power back on at the circuit breaker. It is normal for the dishwasher to run a short drain cycle when power is first restored. Once it stops, you can run a complete test cycle.

Select a Short Rinse 
or Normal Wash

Select a short rinse or normal wash cycle and press start. As the dishwasher begins to fill with water, listen for any unusual noises and check all your connections—the water supply line at both ends and the drain hose connection—for any signs of leaks. Let the dishwasher run through the entire cycle.

During the cycle, open the door once or twice (the cycle will pause) to ensure water is spraying correctly from the spray arms.

As the cycle progresses to the drain phase, check the drain hose connection under the sink again to ensure there are no leaks as water is pumped out. Once the cycle completes successfully without any leaks or errors, your installation is complete. You can now load it up with dishes and enjoy the convenience of your new Whirlpool dishwasher.

Congratulations on a successful DIY project. Following these steps on how to install a whirlpool dishwasher can ensure a smooth and successful installation. However, it is important to note that every dishwasher model may have slightly different steps or requirements. It is always recommended to refer to the manufacturer’s instructions for specific details on your particular model.

Safety Tips

Always prioritize safety during installation. Begin by shutting off both the electrical power at the circuit breaker and the water supply at the shut-off valve. Wear heavy-duty gloves to protect your hands from sharp edges on the appliance and cabinetry, and use safety glasses to shield your eyes from debris.

When moving the dishwasher, ask for help to avoid straining your back. Use a voltage tester to confirm the power is off before touching any wires. Keep towels and a bucket handy to manage any water spillage and prevent slipping hazards.

Common Mistakes to Avoid

A few common mistakes can lead to problems down the line. One is forgetting to create a high loop in the drain hose, which can cause dirty water to flow back into the dishwasher. Another is overtightening water and electrical connections, which can strip threads or crack plastic fittings.

Overtightening Water and 
Electrical Connections

Also, ensure you knock out the plug on a new garbage disposal before attaching the drain hose. Failing to level the dishwasher can result in poor cleaning performance and leaks. Finally, always double-check for leaks after turning the water back on.

Do You Need To Use Professionals?

While installing a dishwasher is a manageable DIY project for many, there are times when calling a professional is the best choice. If you are not comfortable with plumbing or electrical work, it is safer to hire a licensed plumber or electrician. If your installation requires drilling through a granite countertop or installing new cabinetry, a professional will have the right tools and experience.

Additionally, if the existing plumbing or wiring is old or not up to code, an expert can ensure everything is brought up to current standards, preventing future issues.

How Much Will It Cost?

The cost of installing a Whirlpool dishwasher yourself is minimal, typically under $50. This usually covers the price of a dishwasher installation kit, which includes a new water supply line and necessary fittings like the 90-degree elbow.

However, if you choose to hire a professional, the cost can range from $150 to $400, depending on your location and the complexity of the job. This price may increase if new plumbing lines, electrical outlets, or significant cabinet modifications are required for the installation.

Frequently Asked Questions

Q1: Can I Use the Old Water Supply Line and Drain Hose?

A1: It is strongly recommended to replace the water supply line and drain hose with new ones. Over time, these parts can become brittle, cracked, or clogged with mineral deposits, increasing the risk of leaks and blockages. A new installation kit is inexpensive and provides peace of mind that your connections are secure and reliable for years to come. Using old parts may also void your new appliance’s warranty.

 Strongly Recommended to 
Replace the Water Supply

Q2: How Long Does Installation Take?

A2: For a homeowner with some DIY experience, replacing an existing dishwasher typically takes about two to three hours. This includes time for removing the old unit, preparing the space, installing the new one, and testing it. If you are installing a dishwasher in a space for the first time, the project will take longer, as it will involve running new plumbing and electrical lines, which could extend the project over a day or more.

Q3: What Do I Do If My Dishwasher Is Not Level?

A3: A level dishwasher is essential for proper function. If your dishwasher is not level, you will need to adjust the four legs at its base. Most Whirlpool models have front legs that can be turned with pliers or a wrench. The rear legs are often adjusted by a screw mechanism located at the front base of the unit. Place a level inside the dishwasher on the bottom rack track to check for levelness from front-to-back and side-to-side, adjusting the legs until the bubble is centered.

Adjust the Four Legs 
at Its Base

Conclusion

Installing your new Whirlpool dishwasher is a project you can confidently tackle with the right preparation and guidance. By following these detailed steps on how to install a whirlpool dishwasher, from preparing the space and handling connections to securing and testing the unit, you ensure a safe and successful setup.

Remember to prioritize safety at every stage and double-check your work as you go. Now, you are ready to enjoy the performance and convenience of your new appliance for many years to come.