Written By :

Connor

/

/

Dishwasher

Expert Author

How to Test Dishwasher Motor

When your dishwasher stops cleaning dishes properly or starts making a loud humming noise without spraying water, the problem often points to its motor. The ...

When your dishwasher stops cleaning dishes properly or starts making a loud humming noise without spraying water, the problem often points to its motor. The motor is the heart of the appliance, responsible for circulating water through the spray arms. If it fails, the entire cleaning process comes to a halt.

While this sounds like an expensive repair call waiting to happen, you can often diagnose the issue yourself with a few basic tools. This guide will provide clear, beginner-friendly instructions on how to test dishwasher motor, helping you determine if a simple repair or a full replacement is necessary.

How to Test Dishwasher Motor

A malfunctioning dishwasher can quickly disrupt daily routines, leaving you with the tedious task of hand washing dishes. Before calling a professional, taking a few moments to troubleshoot the problem can save time and money. Understanding how the motor functions and learning to test it effectively are key steps in resolving the issue. With the right approach and tools, you can identify the cause and decide on the best solution.

Troubleshooting Common Dishwasher Motor Issues

  • Motor Not Running: If your dishwasher is not running at all, the motor may be the culprit. Start by checking if the dishwasher is receiving power and that there are no tripped circuit breakers or blown fuses. Next, inspect the door latch to ensure it is properly closed. If both of these factors check out, then you should test the motor for continuity using a multimeter. If there is no continuity, then replacing the motor will likely solve the issue.
  • Loud Noises from Motor: A noisy dishwasher can be annoying and disruptive. In most cases, loud noises coming from the motor indicate a damaged or worn out motor. In this case, replacing the motor will likely solve the issue. However, it is also important to check for loose or damaged components that may be causing excessive vibrations and noise.
  • Leaking Water: If you notice water leaking from your dishwasher, it could be due to a number of reasons such as a worn door seal, clogged drain hose, or faulty water inlet valve. Check these components and replace them if necessary to prevent further leaking and potential damage to your kitchen floor.

Step-by-Step Guide on How to Test Dishwasher Motor

Step 1: Disconnect Power and Water Supply

Before starting any appliance repair, safety must be your top priority. You must completely disconnect the dishwasher from all power and water sources. Go to your home’s main electrical panel and flip the circuit breaker that supplies power to the dishwasher to the “Off” position. For an extra layer of safety, use a non-contact voltage tester to confirm there is no electrical current reaching the appliance. Next, locate the hot water supply valve, typically found under the kitchen sink, and turn it fully clockwise to shut off the water flow.

You Must Completely 
Disconnect the Dishwasher

Step 2: Remove the Dishwasher from its Cabinet

To access the motor, you will need to slide the dishwasher out from under the countertop. Start by placing towels on the floor to catch any residual water. Under the sink, you will need to disconnect the drain hose from the garbage disposal or sink drainpipe. You will also need to disconnect the water supply line from the shutoff valve. Finally, remove the screws from the mounting brackets that secure the dishwasher to the countertop. With all connections free, you can now carefully pull the dishwasher straight out of its enclosure.

Step 3: Locate the Motor

With the dishwasher removed, gently lay it on its back on the towels or a piece of cardboard to protect your floor. This position gives you direct access to the components on the underside of the unit. The main circulation motor is typically the largest component you will see, located near the center of the base, connected to the sump assembly. It will have several wires leading to it. Take a moment to inspect the motor and the surrounding area for any obvious signs of trouble, such as leaks, burn marks, or cracked wiring before you proceed.

Gently Lay It on Its 
Back on the Towels

Step 4: Disconnect the Motor’s Wiring Harness

Before you can test the motor, you must disconnect it from the dishwasher’s electrical system. The motor will have a wiring harness, which is a plastic connector with several wires leading into it. This harness clips securely onto a terminal block on the motor. Carefully unclip the harness by depressing its locking tab and pulling it straight off. Avoid pulling on the wires themselves, as this can cause damage. Once the harness is disconnected, the motor is electrically isolated, allowing you to safely perform a continuity test on its windings.

Step 5: Set Up Your Multimeter

A multimeter is the essential tool for this job. This device measures electrical properties, and for this test, you will be checking for continuity. Continuity simply means that there is a complete electrical circuit, which is necessary for the motor to run. Turn the dial on your multimeter to the continuity setting, which is often indicated by a symbol that looks like a sound wave or a diode. When you touch the two multimeter probes together, the device should beep or display a reading of zero, confirming that it is working correctly.

Multimeter is the Essential Tool for This Job

Step 6: Test the Motor Windings for Continuity

Now you will test the electrical windings inside the motor. Look at the terminal block on the motor where you disconnected the wiring harness. You will see several metal prongs or pins. Touch one multimeter probe to one of the motor terminals and the other probe to another terminal. A functioning motor should show a reading indicating a closed circuit (a low resistance value, not infinite) and may beep. Test all possible combinations of terminals. If you get a reading of “OL” (open loop) or infinity between any two terminals, it means there is a break in the motor windings.

Step 7: Check for a Short to Ground

A motor can also fail if it has an electrical short to its metal casing, known as a short to ground. To test for this, keep your multimeter on the continuity setting. Place one probe firmly against a clean, unpainted metal part of the motor’s housing. Then, touch the other probe to each of the electrical terminals one by one. In every case, the multimeter should show no continuity—it should not beep, and the reading should remain at “OL” or infinity. If you get a beep or a continuity reading, it confirms the motor is shorted and is faulty.

Place One Probe 
Firmly Against a Clean

Step 8: Manually Spin the Motor’s Impeller

Sometimes the motor is electrically sound but mechanically seized. The impeller is a small fan-like component that moves the water. It may be part of the circulation motor or a separate pump motor assembly. If you can see and access the impeller, try to spin it by hand. It should turn with some resistance but should not be completely stuck. If it doesn’t move at all, it’s likely jammed by a piece of debris like a shard of glass or a piece of plastic. If it’s clear but still won’t turn, the motor’s internal bearings have likely failed.

Frequently Asked Questions

What Are the Signs of a Bad Dishwasher Motor?

The most common symptoms of a failing dishwasher motor include:

  • A loud humming or buzzing noise without any water spraying.
  • The dishwasher fills with water but the wash cycle never starts.
  • The dishes come out still dirty because water is not being circulated.
  • The dishwasher stops mid-cycle.
  • You notice a burning smell coming from the appliance.

Is It Worth Replacing a Dishwasher Motor?

This depends on the age of your dishwasher and the cost of the replacement motor. For a newer, more expensive dishwasher, replacing the motor can be a cost-effective repair that extends the appliance’s life for several more years. For an older, less expensive model, the cost of the motor plus your time might be close to the price of a brand-new dishwasher with a full warranty.

What Is a Multimeter and Where Do I Get One?

A multimeter is a handheld electronic measuring tool used to test voltage, current, and resistance. For this project, you use its continuity test function. You can buy a basic digital multimeter for a very reasonable price at any home improvement store, electronics store, or online retailer. It’s an incredibly useful tool for any homeowner to have for diagnosing a wide range of electrical issues.

Can a Clogged Filter Mimic a Bad Motor?

Yes, to some extent. A severely clogged filter can prevent water from reaching the pump, which might cause the motor to make a straining or humming noise. Before you assume the motor is bad, always perform basic maintenance first. Remove and thoroughly clean the dishwasher’s filter, which is located at the bottom of the tub, to see if that resolves the issue.

What’s the Difference Between a Circulation Motor and a Drain Pump?

A dishwasher has two main motors. The circulation motor (or wash pump) is the large motor responsible for taking water from the bottom of the tub and powerfully spraying it through the wash arms to clean the dishes. The drain pump is a smaller motor that activates at the end of the cycle to pump the dirty water out of the dishwasher and into your sink’s drain.

Conclusion

Testing your dishwasher’s motor is a manageable task that can save you from an unnecessary repair bill or a premature replacement of your appliance. By following a safe and methodical process—disconnecting the power, accessing the motor, and using a multimeter to check for continuity—you can confidently determine the health of the component.

This knowledge empowers you to make an informed decision about whether to repair or replace it. Now that you have a clear plan on how to test dishwasher motor, you can take control of the situation and get your kitchen back in working order.