Written By :

Connor

/

/

Uncategorized, Dishwasher

Expert Author

How to Drain Whirlpool Dishwasher

A puddle of murky water at the bottom of your Whirlpool dishwasher after a cycle is a frustrating sight. This standing water not only prevents ...

How to Drain Whirlpool Dishwasher

A puddle of murky water at the bottom of your Whirlpool dishwasher after a cycle is a frustrating sight. This standing water not only prevents your dishes from getting properly clean but can also lead to unpleasant odors and potential damage to the appliance over time. Understanding how to manually drain your dishwasher is a crucial skill for any homeowner, allowing you to address the issue promptly and efficiently.

This guide on how to drain whirlpool dishwasher provides a comprehensive, step-by-step process for safely draining your Whirlpool dishwasher. Tackling this task yourself can save you the time and expense of a professional service call. By following these instructions, you can resolve minor drainage problems, perform essential maintenance, and get your kitchen routine back on track without delay.

Tools and Materials You’ll Need

  • Old towels or rags
  • A large, shallow pan or bucket
  • A plastic cup or small container
  • Pliers
  • A flathead screwdriver
  • A Torx screwdriver (T15 or T20 size, depending on your model)
  • A wet/dry vacuum (optional but highly recommended)
  • Protective gloves

8 Simple Step-By-Step Guidelines on How to Drain Whirlpool Dishwasher

Step 1: Disconnect the Power and Water Supply

Your safety is the top priority when working with any electrical appliance, especially one that involves water. Before you begin any work, you must completely disconnect the dishwasher from its power source. For most installations, this means unplugging the power cord from the wall outlet, which is typically located under the kitchen sink. If the outlet is hard to reach or the dishwasher is hardwired, you must go to your home’s main circuit breaker box and switch off the breaker dedicated to the dishwasher. Confirm the power is off by trying to start a cycle on the control panel; it should be completely unresponsive.

Once the power is safely disconnected, you also need to shut off the water supply to the appliance. The water supply valve is usually located under the sink, connected to the hot water line. It will have a small handle that you need to turn clockwise until it is firmly closed. This step prevents any new water from entering the dishwasher while you are working on it, avoiding further flooding and making the draining process more manageable. Place some old towels on the floor in front of the dishwasher to prepare for any spills.

Step 2: Remove the Bottom Dish Rack and Unload Dishes

With the power and water safely turned off, you can now access the interior of the dishwasher. Open the dishwasher door fully and carefully remove any remaining dishes, glasses, and silverware. Place them in the sink or on a countertop out of the way.

Carefully Remove Any Remaining 
Dishes, Glasses, and Silverware

This clears your workspace and prevents anything from being damaged or obstructing your view of the standing water and filter area at the bottom of the tub. Taking everything out gives you unrestricted access to the components you need to inspect and clean.

After the dishes are removed, slide the bottom dish rack completely out of the dishwasher and set it aside. This large rack is the main obstacle preventing you from reaching the filter, spray arm, and the sump area where the water collects. With the lower rack out of the way, you will have a clear, unobstructed space to work in. This makes it much easier to see the extent of the standing water and to begin the manual draining process effectively.

Step 3: Manually Bail Out the Standing Water

Now you need to remove as much of the standing water from the bottom of the dishwasher tub as possible. Using a small plastic cup or container, carefully scoop out the water and pour it into a bucket or directly into your sink. Continue this process until you have removed the bulk of the water. Be prepared for the water to be dirty and to contain food particles. Wearing protective gloves is a good idea during this step. Getting most of the water out manually makes the subsequent steps less messy.

 Remove as Much of the Standing Water 
From the Bottom of the Dishwasher Tub

For a more thorough removal of the remaining water, a wet/dry vacuum is an excellent tool. Switch the vacuum to its “wet” setting and use the hose attachment to suction out the last puddles from the dishwasher’s sump pit and the surrounding tub floor. This method is faster and more efficient than using a sponge and ensures the area is as dry as possible before you proceed to inspect the filter and drain hose. Having a dry workspace is crucial for identifying clogs or blockages accurately.

Step 4: Clean the Dishwasher Filter and Sump

The most common cause of a Whirlpool dishwasher not draining is a clogged filter. The filter assembly is located at the bottom of the tub, usually beneath the lower spray arm. It typically consists of an upper filter cup and a lower coarse filter screen. To remove it, twist the upper filter cup (often a quarter-turn counter-clockwise) and lift it straight out. Then, you can lift out the lower filter screen.

These components are designed to trap food particles and prevent them from clogging the drain pump.

Thoroughly wash both parts of the filter assembly under warm, running water. Use a soft brush, like an old toothbrush, to gently scrub away any accumulated grime, grease, and trapped food debris. Pay close attention to the fine mesh of the filter, as it can get easily clogged.

While the filter is removed, use a cloth or sponge to wipe down the sump area where the filter sits. Inspect the sump for any larger debris that may have bypassed the filter and remove it. A clean filter is essential for proper drainage.

Step 5: Inspect the Lower Spray Arm

With the filter removed and the sump area clean, take a moment to inspect the lower spray arm. This arm rotates during the wash cycle to distribute water evenly over the dishes. The small holes, or jets, on the spray arm can sometimes become clogged with hard water deposits or small food particles. If these jets are blocked, it can affect the dishwasher’s cleaning performance and, in some cases, interfere with proper water flow and drainage dynamics within the tub.

Take a Moment to Inspect 
the Lower Spray Arm

To inspect it, you can usually lift the spray arm straight up and off its mount. Hold it up to a light source to see if any of the jets are blocked. If you find any obstructions, use a toothpick, a small piece of wire, or a pair of needle-nose pliers to carefully clear them out. After clearing the jets, rinse the entire spray arm under running water to flush out any remaining debris. Once it’s clean, place it back onto its mounting post, ensuring it can spin freely by giving it a gentle push.

Step 6: Check the Drain Hose for Kinks and Clogs

The drain hose is the pathway water takes from the dishwasher to your sink’s plumbing or garbage disposal. A kink or a clog in this hose is another frequent reason for draining issues. The hose is a flexible, ribbed plastic tube that runs from the dishwasher’s drain pump, usually through the kitchen cabinetry, to its connection point under the sink. Begin by visually inspecting the entire accessible length of the hose for any sharp bends or kinks that could be restricting water flow. Straighten out any that you find.

If there are no visible kinks, the hose may be clogged internally. To check this, you will need to disconnect it from where it attaches to the garbage disposal or the sink’s drain pipe.

Place a shallow pan under the connection point to catch any residual water. Use pliers to loosen the metal clamp holding the hose in place, and then carefully pull the hose off the connection nipple. Aim the end of the hose into a bucket and check if trapped water flows out. You can also use a plumber’s snake or a long, flexible wire to gently probe the hose for blockages.

Step 7: Clear the Garbage Disposal Connection

If your Whirlpool dishwasher drains into a garbage disposal, the connection point itself can be a source of blockage. This is especially common if the garbage disposal was recently installed and the knockout plug was not removed. This small plastic plug inside the disposal’s dishwasher inlet nipple is designed to seal the opening if a dishwasher is not connected. To check this, you will need to disconnect the drain hose from the disposal as described in the previous step.

Once the hose is disconnected, carefully insert a screwdriver or your finger into the disposal’s inlet nipple. You should feel an open passage. If you feel a solid barrier, the knockout plug is still in place and needs to be removed. To remove it, use a screwdriver and a hammer to gently tap the plug from the outside until it breaks free and falls into the disposal’s grinding chamber. Reach into the disposal (ensure it is completely powered off) and remove the plastic piece. This simple oversight is a very common cause of brand-new dishwasher installations failing to drain.

Step 8: Reassemble and Test the Dishwasher

After you have thoroughly cleaned the filter, checked the drain hose, and cleared any potential clogs, it is time to put everything back together. Reinstall the lower filter screen and then lock the upper filter cup back into place by turning it clockwise.

Reinstall the Lower Filter Screen and 
Then Lock the Upper Filter Cup

Place the bottom dish rack back on its track inside the dishwasher. Reconnect the drain hose to the garbage disposal or sink drain, making sure to tighten the clamp securely to prevent leaks. Once all internal components are secure, you can restore the water and power.

Turn the water supply valve back on (counter-clockwise) and plug the dishwasher back in or flip the circuit breaker on. To test if the problem is solved, run a short cycle. The “Rinse Only” or “Drain” cycle is perfect for this. Listen for the sound of the drain pump activating and watch to see if the water drains completely from the tub at the end of the cycle.

If the water drains successfully, you have fixed the issue. If water remains, there may be a more serious problem with the drain pump or a blockage further in your home’s plumbing, which may require professional assistance.

Following these steps on how to drain whirlpool dishwasher, you can effectively troubleshoot and resolve any issues with draining. However, it is also important to properly maintain your dishwasher to avoid future drainage problems.

Frequently Asked Questions

Q1: Why Is There Always Standing Water in the Bottom of My Whirlpool Dishwasher?

A1: Finding a small amount of clean water (about a cup) in the sump area at the bottom of your dishwasher is actually normal. This water helps keep the pump seals lubricated and prevents them from drying out and cracking.

However, if you see a significant amount of murky, dirty water covering the bottom of the tub after a cycle, it indicates a drainage problem. The most common causes are a clogged filter, a kinked drain hose, or a blockage in the connection to your garbage disposal or sink drain.

Q2: How Often Should I Clean My Whirlpool Dishwasher Filter?

A2: For optimal performance and to prevent drainage issues, it is recommended to clean your Whirlpool dishwasher filter regularly. For households that run the dishwasher daily, checking and rinsing the filter at least once a month is a good practice. If you tend to pre-rinse your dishes thoroughly before loading, you may be able to extend this to every few months. However, if you notice food particles on your clean dishes or a gritty residue in the tub, you should clean the filter immediately.

Q3: Can I Run My Garbage Disposal While the Dishwasher Is Draining?

A3: It is generally not recommended to run your garbage disposal while the dishwasher is actively draining. Both appliances share the same drain pipe under the sink. Running the disposal can create backflow, forcing food waste and dirty water back up the drain hose and into your dishwasher tub. This can redeposit grime onto your clean dishes and potentially create a new clog. It is best practice to wait until the dishwasher has fully completed its drain cycle before using the garbage disposal.

Q4: What Does It Mean if My Dishwasher Makes a Humming Noise but Does Not Drain?

A4: A humming or buzzing sound coming from your dishwasher during the drain cycle without any water being removed often points to a problem with the drain pump. The sound indicates that the pump’s motor is receiving power but is unable to operate. This could be caused by a blockage, such as a piece of glass or a fruit pit, physically jamming the pump’s impeller. In other cases, it could signify that the drain pump motor itself has failed and will need to be professionally inspected and likely replaced.

 Regular Maintenance, 
Especially Cleaning the Filter

Conclusion

Successfully diagnosing and fixing a Whirlpool dishwasher that won’t drain is an empowering task for any homeowner. By systematically working through these steps on how to drain whirlpool dishwasher—from disconnecting the power to cleaning the filter and inspecting the hoses—you can resolve the most common issues that lead to standing water.

This not only saves you from the inconvenience of a non-functioning appliance but also helps you avoid a potentially costly service call. Regular maintenance, especially cleaning the filter, is the best way to prevent future drainage problems. With these skills, you can ensure your dishwasher continues to operate efficiently, keeping your dishes sparkling clean for years to come.