Written By :

Connor

/

/

Dishwasher

Expert Author

How to Troubleshoot Dishwasher Diverter Motor

When you run a cycle and your dishes come out just as dirty as they went in, it’s incredibly frustrating. If you notice that only ...

When you run a cycle and your dishes come out just as dirty as they went in, it’s incredibly frustrating. If you notice that only one rack is getting clean or the water doesn’t seem to be spraying effectively, the issue might not be the soap or the water pressure. A small but vital component called the diverter motor could be the culprit. This motor directs water to either the upper or lower spray arms, and when it fails, your dishwasher can’t clean properly. This guide will provide clear, beginner-friendly instructions on how to troubleshoot dishwasher diverter motor issues, helping you diagnose the problem and get your appliance working again.

How to Troubleshoot Dishwasher Diverter Motor

A malfunctioning dishwasher can disrupt your daily routine, but understanding the basics of its components can save you time and money on repairs. The diverter motor is a crucial part of your dishwasher that ensures water is sprayed where it’s needed. By learning how to troubleshoot this small yet essential component, you can address washing performance issues efficiently and restore your dishwasher’s functionality without unnecessary stress.

Identifying the Problem

When your dishwasher is not cleaning dishes properly, one of the first components to check is the diverter motor. This motor controls the flow of water between the upper and lower spray arms, ensuring that water reaches all areas within the appliance. If the diverter motor fails or becomes faulty, it can result in uneven spraying or even a complete lack of water reaching certain areas. This can lead to dirty dishes and an inefficient cleaning process.

Troubleshooting Tips

Before attempting any repairs on your dishwasher, it’s essential to make sure you have unplugged it from its power source. Safety should always be a top priority when dealing with any electrical appliances. Once unplugged, follow these steps to troubleshoot a potential issue with your dishwasher:

  1. Check the power source – Make sure that your dishwasher is properly plugged in and that the outlet is functioning correctly. You can test this by plugging in another appliance or using a voltage tester.
  2. Inspect the door latch – The door latch plays a crucial role in ensuring that your dishwasher stays closed during operation. If it’s damaged or not latching correctly, it can cause your machine to not start.
  3. Examine hoses and connections – Leaks in hoses or loose connections could be the culprit behind a malfunctioning dishwasher. Make sure all hoses are tightly secured and free of any holes or cracks.
  4. Clean filters and drain – A clogged filter or drain can prevent water from properly draining out of the dishwasher, leading to standing water and a foul smell. Regularly cleaning these components can help keep your dishwasher running smoothly.
  5. Check for error codes – If your dishwasher has an electronic display, it may show an error code when there is a problem. Refer to your owner’s manual to troubleshoot the issue or contact a professional technician for assistance.

Step-by-Step Guide on How to Troubleshoot a Dishwasher Diverter Motor

Step 1: Understand the Symptoms of a Bad Diverter Motor

Before you start taking things apart, it’s important to confirm the symptoms match a potential diverter motor failure. The most common sign is poor cleaning performance, where dishes on one rack (usually the top one) remain dirty after a full cycle. You might also hear unusual noises, such as a grinding or clicking sound, at specific points during the wash cycle as the motor attempts to switch water flow. In some cases, the dishwasher may stop mid-cycle and display an error code related to water circulation. Recognizing these specific signs helps confirm you are on the right track.

Step 2: Disconnect Power and Water for Safety

Safety is the most important step in any appliance repair. Before you begin any diagnostic work, you must completely disconnect the dishwasher from its power source. Go to your home’s circuit breaker panel and flip the breaker that controls the dishwasher to the “Off” position. For added safety, you can also unplug the dishwasher from the wall outlet if it is accessible. Next, turn off the water supply. The shut-off valve is typically located under the kitchen sink and connected to the hot water line. This prevents any electrical shock or accidental flooding while you work.

Step 3: Access the Motor

The diverter motor is located on the underside of the dishwasher tub, usually near the main circulation pump. To access it, you will need to pull the dishwasher out from under the counter. You may need to remove a few mounting screws that secure the dishwasher to the countertop. Once it’s free, carefully lay the dishwasher on its back or side on a soft towel or blanket to protect your floor and the appliance. This position will give you a clear view of the components on the bottom, including the diverter motor and its wiring.

The Diverter Motor is
Located on the Underside

Step 4: Perform a Visual Inspection

With the motor exposed, the first diagnostic step is a thorough visual inspection. Look for any obvious signs of damage. Check for cracks in the motor housing, burnt or melted plastic, or signs of water leakage around the diverter motor seal. A failed seal is a common problem that allows water to drip onto the motor’s electrical components, causing it to short out and fail. If you see white, crusty mineral deposits or signs of rust around the motor, it’s a strong indication that the seal has failed and both the seal and the motor will likely need to be replaced.

Step 5: Test the Motor with a Multimeter

If the visual inspection reveals no obvious damage, the next step is to test the motor for electrical continuity. This is a key part of learning how to troubleshoot dishwasher diverter motor electronics. Set your multimeter to the resistance or Ohms setting (Ω). Disconnect the wire harness from the diverter motor to expose its electrical terminals. Touch the multimeter probes to the two terminals on the motor. A functional diverter motor should give a resistance reading, typically between 2,000 and 4,000 ohms, though this can vary by model. If the multimeter shows no reading (infinite resistance), the motor’s internal circuit is broken, and it needs to be replaced.

Test the Motor for
Electrical Continuity

Step 6: Inspect the Diverter Disc and Spray Arms

Sometimes, the motor itself is fine, but its movement is obstructed. The diverter motor’s job is to rotate a plastic disc that opens and closes ports, directing water to the different spray arms. Check to see if this disc is cracked, warped, or blocked by debris. You should also check the spray arms themselves. Remove the bottom rack and spin the lower and middle spray arms by hand. If they do not rotate freely, it could be due to a clog in the hub or an obstruction, which might make you think the diverter is failing when it’s actually a different issue.

Step 7: Listen During a Test Cycle

If you are unable to find the fault with a visual inspection or multimeter test, you can carefully perform an auditory test. Reconnect the wiring, place the dishwasher upright, and reconnect the power and water. Start a new wash cycle and listen carefully during the first few minutes. You should hear the dishwasher fill with water, followed by the sound of the circulation pump starting. Shortly after, you should hear a faint whirring or clicking sound as the diverter motor shifts position. If you hear a loud grinding, repeated clicking, or no sound at all from the motor area, it strongly suggests the motor is failing mechanically.

Frequently Asked Questions

What Does a Dishwasher Diverter Motor Do?

A dishwasher diverter motor is a small motor that controls the flow of water to the different spray arms inside the dishwasher. It rotates a valve or disc that alternates the water supply, typically between the lower spray arm and the upper/middle spray arms. This ensures that all dishes, on both racks, receive a powerful spray of water for effective cleaning throughout the wash cycle.

Receive a
Powerful Spray of Water

What Are the Signs of a Bad Diverter Motor?

The most common symptoms of a failing diverter motor include:

  • Dishes on one rack (usually the top) are not getting clean.
  • A humming, grinding, or loud clicking noise during the cycle.
  • The dishwasher stops mid-cycle and may show an error code related to water distribution.
  • Water pressure from the spray arms seems weak.

Can a Clogged Filter Mimic a Bad Diverter Motor?

Yes, absolutely. A clogged dishwasher filter can reduce overall water pressure, leading to poor cleaning performance that might be mistaken for a diverter motor issue. Before you begin troubleshooting the motor, always remove and thoroughly clean the dishwasher’s filter, which is located at the bottom of the tub. This simple maintenance step solves many cleaning problems.

Is It Worth Replacing a Diverter Motor?

In most cases, yes. A diverter motor is a relatively inexpensive part, and replacing it yourself can save you hundreds of dollars compared to buying a new dishwasher or hiring a repair technician. The replacement process is generally straightforward for someone with basic DIY skills. If your dishwasher is otherwise in good condition, replacing the diverter motor is a very cost-effective repair.

How Much Does a Dishwasher Diverter Motor Cost?

The cost of a replacement diverter motor can vary depending on your dishwasher’s brand and model, but they are generally affordable. You can typically expect the part to cost between $40 and $100. Be sure to order the exact part for your specific model number to ensure it fits and functions correctly.

Conclusion

A malfunctioning dishwasher can be a major inconvenience, but you don’t always need to call a professional for help. By learning the common symptoms and following a logical diagnostic process, you can often pinpoint the problem yourself. Testing for electrical continuity, inspecting for leaks, and listening for unusual sounds are all effective methods for determining if the diverter motor is the source of your troubles. Now that you have a better understanding of how to troubleshoot dishwasher diverter motor issues, you can approach the repair with confidence and get your appliance back to keeping your dishes sparkling clean.